Titanium® UDL50


UDL50 is a heavy duty premium synthetic roofing underlayment
for use under all: Metal, Synthetic, Ceramic, Clay, Slate, Concrete & Shingle roofing.


Titanium UDL50

Premium heavy duty air, water and vapor barrier for use under: Metal, Tile, Slate, Shake & Shingle roofing



  • Patented SURE-FOOT® slip resistant nodular walking surface and an advanced resin technology that provide superior steep slope walkability
  • Lifetime limited warranty
  • Tougher, thicker robust construction that can withstand harsh environmental conditions
  • Up to 6 months UV exposure rating
  • Meets and exceeds ASTM D226 Types I & II
  • ICC ES Approved
  • Class A Fire ASTM E108
  • CAN/CSA A220.1
  • Meets Class 4 Hail Rating
  • Florida Building Code Approved
  • Texas Department of Insurance
  • 5 times lighter & 25 times stronger than 30 lb felt
  • Contributes to LEED® points, 100% Recyclable
  • All temperature performance -40°F to 240°F
  • Synthetic construction inert to mold growth
  • Cool gray surface, doesn’t expand or contract
  • Dual logo custom printing available



Titanium® UDL50 is a highly engineered, mechanically attached coated woven synthetic roofing underlayment for sloped roofs. UDL50 is the first product for sloped roofs to address high end primary roofing products with long life warranties such as metal, clay & concrete tiles, slate and heavy weight laminated asphalt shingles. UDL50 used in conjunction with Titanium PSU30 self adhered underlayment for ice damming and valley areas, offers the sloped roofing industry a truly revolutionary system of safety, security and simplicity... two products (UDL50 & PSU30) are ALL your premium roofing systems need.

UDL50 advanced polymers combine to deliver a unique gray synthetic roofing underlayment that can be used under all types of primary roofing materials to replace 30 lb felt. Gray technology provides for a cooler working surface during installations and up to a 6 month UV exposure. Unlike smooth surfaced underlayments, Titanium UDL50 possesses a revolutionary patented slip resistant Sure-Foot® nodular walking surface technology that allows for easier steep slope walkability.

UDL50 is 25 times stronger than 30 lb felt, gone are the days of blow-offs and call backs! A 10 square roll weighs only 48 lbs! This super low weight combined with 48” width and 250 ft. run length means big savings in time and labor (over 30% faster to install than felt!). Fewer laps, cuts and roll handling means you can do more jobs in less time. Inventory fewer rolls and gain an edge in productivity and profits.

UDL50 is 100% synthetic, therefore totally unaffected by water, which means it is 100% inert to mold, lays flat, will not wrinkle and you can leave your roof uncovered without the need for tarps or immediate dry-in. Unlike felts, UDL50 does not dry out, leach oils in the heat, nor does it become stiff, difficult to roll or crack in the cold.

UDL50 with its advanced composition and thicker more robust construction is designed for heavy duty applications. Combining the unique features of UDL50 with a 6 month UV exposure rating means your job will stay on track through all kinds of wind and weather. Less material damage and waste during installation and fewer post-install repairs result in significant savings in time and money. UDL50 will continue to protect your high end primary roofing products long after felt has turned to dust!

Roofing Contractor Customer Loyalty Program

Get rewarded with a $100 gift card for every 30 rolls of Titanium® underlayment purchased up to a maximum value of $3000! Terms & Conditions apply. Click here for details

Titanium Signature Roofers

With a Titanium Signature Roofer you can be assured of the highest quality underlayment installation by one of the industries finest roofers.Click here for details




Installation Instructions

Titanium® UDL50 is an air, water and vapor barrier (.06 perms) and therefore should be installed above a properly ventilated space(s). It is recommended to follow all building codes applicable to your geographical region and structure type.

DECK PREP: All protrusions from the deck area must be removed and ensure the deck has no voids, damaged or unsupported areas. Deck surface should be free of debris, dry and moisture free.

USE: Titanium UDL50 must be covered by primary roofing within 180 days of application. UDL50 is designed for use under; Asphalt Shingles, Synthetic Shingles, Metal roofing, Tiles, Slate and Cedar Shakes.

APPLICATION: For slopes 2:12 and higher UDL50 is to be laid out horizontally (parallel) to the eave with the printed side up. Horizontal laps should be 4" and vertical laps should be 6"and anchored approximately 1" in from the edge. For low slope applications it is recommended to overlap 50% plus 1", for complete definition of low slope and guidelines consult authorities having jurisdiction. UDL50 product is not recommended for slopes less than 2:12. The use of a roofing hammer, hatchet hammer, pneumatic air or gas driven fastener tools is acceptable. The use of a straight edge cutting knife is recommended.

FASTENERS: For same day coverage with primary roofing UDL50 can be anchored with corrosive resistant 3/8" head x 1" leg roofing nails (ring shank preferred, smooth leg acceptable). The use of every other anchoring location printed on the product is also acceptable.

ANCHORING: All anchoring nails must be flush, 90 degrees to the roof deck, and tight with the underlayment surface and the structural roof deck. Where seams and joints require sealant or adhesive use a low solvent plastic roofing cement meeting ASTM D-4586 Type 1, or Federal Spec SS-153 Type 1 such as Karnak, Henry, DAP, MB, Geocel or equivalent. Acceptable alternatives are butyl rubber, urethane, and EDPM based caulk or tape sealant.

EXTENDED EXPOSURE: If Titanium UDL50 product will be exposed longer than 1 day but less than 5 days then it is recommended to anchor using corrosive resistant 3/8" head x 1" leg roofing nails (Ring shank preferred). For exposure more than 5 days and up to 180 days UDL50 product must be anchored with 1" plastic or metal cap smooth or ring shank roofing nails. Miami-Dade approved tin tags or metal caps are also acceptable, and it is recommended for best performance to use with the rough edge facing up. For extended exposure it is always recommended to anchor on every printed position on the facer. Note: UDL50 is not designed for indefinite outdoor exposure. For extended exposure conditions where driving rain or strong winds are expected it is recommended to take additional precautions such as doubling the lap widths. Alternately or in addition to a compatible sealant could be used between the laps or a peel and stick tape could be applied to the overlaps.

CAUTION - READ GOOD SAFETY PRACTICES BELOW
Good safety practices should be followed on steep slope roofs, such as use of tie-offs, toe boards, ladders and/or safety ropes and personal body harnesses. Follow OSHA guidelines. Slip resistance may vary with surface conditions from debris that accumulates, weather, footwear and roof pitch. Failure to use proper safety gear can result in serious injury. Depending on roof pitch and surface conditions, blocking may be required to support materials on the roof and is good safety practice. Remember to seal the nail holes after removing blocking.

Instrucciones de instalación

Titanium® UDL50 es una barrera contra aire, agua y vapor. Debe ser instalado sobre espacios ventilados apropiadamente (siga TODOS los códigos de construcción correspondientes a su zona geográfica y al tipo de estructura en construcción) ya que se considera una barrera contra el vapor (0,05 permeable). El uso de una capa de papel colofonia rojo no es requerido debajo de los sistemas de techado de metal. Deben eliminarse las zonas salientes de la plataforma y ésta no debe tener espacios vacíos ni áreas dañadas o sin apoyo. Se recomienda el uso de un cortador de borde recto. UDL50 debe ser colocado horizontalmente (paralelo) al alero con el lado del logotipo hacia arriba y con una solapa horizontal de 4 pulgadas (101 mm) y otra vertical de 6 pulgadas (152 mm). Siga los códigos de instalación que han sido clasificados para pendientes bajas entre 2:12 y 4:12, y para pendientes muy inclinadas mayores a 4:12.

FIJACIONES: UDL50 tendrá que sujetarse al material de la estructura de la cubierta del techo usando clavos electro galvanizados (EG) para tejados con una cabeza de 3/8 de pulgada de diámetro; clavos de casquillo de metal; tornillos con tuercas; grapas con tapa de plástico y patas de 7/16 pulgadas como mínimo o clavos de 1 pulgada de largo como mínimo, con casquillo de plástico. Anclaje tiene que ser instalado en una como mínimo en las superficies impresas en el producto, espaciados 6 pulgadas (15 cm) entre centros en los tramos verticales y horizontales, y en 12 pulgadas (30 cm) a lo largo del centro del rollo en el campo. Si el contrapiso será cubierto por techos primaria dentro de los 5 días de la aplicación, y no están sujetas a un tráfico intenso o fuerte viento, a continuación, la opción de utilizar cada otro punto de anclaje impreso en el campo central es aceptable.

Todos los dispositivos de anclaje tienen que estar al mismo nivel, a 90 grados de la cubierta del techo, y ajustados al recubrimiento sintético y a la estructura de la cubierta del techo. En casos de exposición prolongada (meses) o fuertes vientos, duplique como mínimo la anchura de la solapa. Otra opción: doble la solapa sobrepuesta formando un canal de configuración “J” antes de clavar; utilice un sellador compatible entre las solapas o el empleo de una cinta autoadhesiva es altamente recomendado. Para instalaciones aseguradas con tablones de madera, utilice únicamente clavos o tornillos de longitud adecuada, para fijarlos al material de la estructura de la cubierta del techo. Es recomendable el uso de clavos electro galvanizados con una cabeza de 3/8 de pulgada de diámetro, grapas con tapa de plástico, clavos con casquillo de plástico, o tornillos y tuercas de metal o plástico; esto es necesario para asegurar UDL50 y combatir las ráfagas de viento hasta que el sistema de aseguramiento de madera sea instalado. Cuando se usen grapas con tapa de plástico, cada aleta lateral de la grapa debe tener una longitud mínima de 7/16 de pulgada. No instale tablones directamente sobre ninguna tapa de plástico. Si esto sucede remueva las grapas de plástico o clavos con casquillo de plástico y coloque un parche en el orificio, reinstale otro clavo fuera de la estructura de aseguramiento y continúe. En los casos en que las uniones y juntas requieran de material sellador o adhesivo, utilizar cemento plástico para techos de alta calidad, bajo contenido de solvente y libre de amianto que cumpla con las normas ASTM D-4586 Tipo 1 (Libre de Amianto), Especificación Federal SS-153 Tipo 1 (Libre de Amianto), por ejemplo, Karnak, Henry, DAP, MB, Geocel o similar. Otras alternativas posibles son los selladores en forma de cinta o masilla con base de caucho butílico, uretano o EDPM. Dependiendo de la inclinación de la cubierta y de las condiciones de la superficie del techo, puede ser necesaria la obstrucción para sostener los materiales colocados en el techo.

UDL50 no está diseñado para ser expuesto al aire libre indefinidamente. La instalación final del tejado tiene que ser terminada en un plazo máximo de 6 meses.

ADVERTENCIA – LEA LAS SIGUIENTES BUENAS PRÁCTICAS DE SEGURIDAD Al igual que con cualquier producto para tejados, siempre deberá seguir los códigos y prácticas de seguridad (OSHA). Siempre utilice y vista los dispositivos para la protección de caídas cuando se esté trabajando en el techo. Tenga precaución al caminar o al estar de pie sobre TITANIUM UDL50 ya que la tracción puede variar de acuerdo a las condiciones de la superficie, el clima, el calzado utilizado y la inclinación del techo. La falta del calzado y del equipo de seguridad adecuado, puede provocar lesiones graves.

Consignes d'installation

TitaniumMD UDL50 est une barrière contre l’air, l’eau et la vapeur (0,06 perm) et elle doit donc être installée au-dessus d’espaces bien ventilés. Il est recommandé de respecter tous les codes du bâtiment applicables à la région et au type de structure.

PRÉPARATION DU PLATELAGE : Les saillies de la surface du platelage doivent être enlevées et le platelage ne doit pas avoir d’interstices ni d’endroits endommagés ou non supportés. La surface du platelage doit être exempte de débris, sèche et à l’abri de l’humidité.

UTILISATION : Le produit UDL50 doit être couvert par la couverture principale dans les 180 jours suivant sa pose. Le produit UDL50 est conçu pour être posé sous tous les types de couverture principale, y compris les bardeaux d’asphalte, les bardeaux synthétiques, les couvertures métalliques, les tuiles, l’ardoise et les bardeaux de fente en cèdre.

APPLICATION : Pour les pentes fortes de 2:12 ou plus, le produit UDL50 doit être disposé horizontalement (parallèlement) par rapport à l’avant-toit, la face imprimée vers le haut. Les chevauchements horizontaux doivent être de 4 po et les chevauchements verticaux doivent être de 6 po et ancrés à environ 1 po du bord. Pour les pentes douces, il est recommandé de faire chevaucher de 50 % plus 1 po; pour voir une définition complète du terme « pente douce » et les lignes directrices à cet égard, veuillez consulter les autorités compétentes de votre région. Le produit UDL50 n’est pas recommandé sur les pentes de moins de 2:12. L’emploi de marteaux à toiture, d’un marteau hachette ou de cloueuses pneumatiques ou à gaz est acceptable. On conseille d’utiliser un couteau à lame droite.

FIXATIONS : Si le produit Titanium UDL50 doit être exposé à l’air libre pendant moins de 5 jours avant l’installation de la couverture principale, il est recommandé de l’ancrer avec des clous de toiture de 1 po (tête de 3/8 po) résistants à la corrosion (l’utilisation de clous à tige crantée est à privilégier). L’usage de tout autre dispositif d’ancrage est acceptable sur le chantier.

ANCRAGE : Tous les dispositifs d’ancrage ou toutes les agrafes doivent être affleurants, enfoncés à 90 degrés dans le platelage, et ne pas présenter de jeu avec la sous-couche et avec la structure du platelage. Lorsque les joints requièrent un produit d’étanchéité ou un adhésif, utilisez de la colle plastique pour feutre à faible teneur en solvant conforme à la norme ASTM D-4586 Type 1, ou à la spécification fédérale SS-153 de type 1 comme les adhésifs Karnak, Henry, DAP, MB, Geocel ou d’autres produits équivalents. Des solutions de rechange acceptables comprennent le butylcaoutchouc, l’uréthane et les calfeutrants ou rubans d’étanchéité à base d’EPDM.

EXPOSITION PROLONGÉE : En cas d’exposition de plus de 5 jours, allant jusqu’à 180 jours, le produit UDL50 peut être ancré avec les fixations suivantes pour offrir un rendement optimal dans de mauvaises conditions météorologiques; (1) clous de toiture à capuchon de plastique ou de métal de 1 po à tige lisse ou à tige crantée, (2) rivets et clous en étain approuvés par Miami-Dade, le bord rugueux face vers le haut, (3) vis et rondelles, (4) clous de toiture de 1 po, à tête de 3/8 po, résistants à la corrosion (clous à tige crantée privilégiés) ou (5) agrafes de 1/2 po à capuchon en plastique, à pattes de 7/16 po au minimum. Dans le cas d’une exposition prolongée, il est toujours conseillé d’ancrer le produit sur chaque position imprimée de la surface. Remarque : Le produit UDL50 n’est pas conçu pour une exposition extérieure prolongée. Dans le cas d’une exposition prolongée ou de la pluie battante ou des vents violents pourraient survenir, il est conseillé de prendre des précautions additionnelles, comme doubler la largeur des chevauchements. Comme solution de rechange ou comme précaution additionnelle, vous pouvez utiliser un produit d’étanchéité compatible entre les chevauchements ou les recouvrir d’une bande adhésive pelée et collée.

MISE EN GARDE — VEUILLEZ LIRE LES CONSIGNES DE SÉCURITÉ CI-DESSOUS
Adoptez toujours de bonnes pratiques de sécurité sur les toits à pente raide; par exemple, servez-vous de cordes de fixation, de planches cale-pied, d’échelles ou de cordes de sécurité et de harnais de sécurité individuels. Veuillez suivre les lignes directrices de l’OSHA. La résistance au glissement peut varier selon l’état de la surface, les débris qui y sont accumulés, les conditions atmosphériques, les chaussures utilisées et la pente du toit. Le fait de ne pas utiliser un équipement de sécurité approprié pourrait entraîner des blessures graves. Selon la pente de toit et l’état de la surface, un calage pourrait être requis pour soutenir les matériaux sur le toit, ce qui est une bonne pratique de sécurité. Souvenez-vous de sceller les trous des fixations qui ont retenu les cales après les avoir enlevées.

Titanium UDL50 Technical Data

UDL50 Roll/Pallet Specs
LENGTH PER ROLL: 250’ / 76.2 m
WIDTH PER ROLL: 48” / 122 cm
WEIGHT PER ROLL: 48 lbs / 21.8 kg
ROLL SIZE: 10 sq / 93 m²
ROLLS PER PALLET: 25
PALLET WEIGHT: 1250 lbs / 567 kg

This product is manufactured in accordance with national standards which allow for non-critical variances in weights and measures. Values are typical data and not limiting specifications. All values ± 10%

Test & Standard UDL50 Typical Value #30 Felt Typical Value
Class A Fire ASTM E108 Pass N/A
Nail Sealability Modified ASTM D1970 Pass N/A
Permeability ASTM E96 0.05 perms 1.75 perms 
Water Transmission ASTM D4869  Pass Pass 
Tear Strength ASTM D4533 MD 55 lbs (25 kg) | CD 55 lbs (25 kg) MD 4 lbs (1.8 kg) | CD 2 lbs (0.9 kg) 
Tensile Strength ASTM D751  MD 178 lbs (81 kg) | CD 176 lbs (80 kg) MD 70 lbs (32 kg) |CD 38 lbs (17 kg) 
Burst Strength ASTM D751  300 psi (2065 kPa) 62 psi (430 kPa) 
Elongation ASTM D751  MD 20 % CD 20 % MD 2% CD 2% 
Weight per Square ASTM D5261  4.7 lbs (2.13 kg) 27.5 lbs ( 12.5 kgs) 
Minimum Thickness ASTM D1777  30 mils (0.75 mm) 60 mils (1.5 mm)
Temperature Range  -40°F to 240°F (-40°C to 115°C)

MD = Machine Direction CD = Cross Direction
Test data is based on an average taken over several production runs and should not be considered or interpreted as minimum or maximum values. Values are typical data and not limiting specifications. All values ± 10%. Dry tested conditions: in water, #30 felt will absorb +30% water and lose +50% strength when wet.

UDL50 Building Codes

Important Letter To: All Florida Building Officials and Building Inspectors. [ VIEW PDF ]

  • Impact Resistance/Hail Testing Report View...
  • ICC-ES ESR-2154 View...
  • MIAMI-DADE NOA No.13-0610.01
  • INTERTEK WARNOCK HERSEY
  • CAN/CSA A123.3 [PDF Report]
  • CLASS A ASTM E-108 Intertek report# 312482MID-007
  • CAN/CSA A220.1 Intertek report # 3124618COQ-005F
  • Florida Building Code (FBC) FL11602 [View PDF]
  • Meets and exceeds ASTM D226

Titanium UDL50 Limited Warranty

InterWrap Corp (the “Seller”) warrants to the purchaser of these goods (the “Buyer”), the product Titanium UDL50 synthetic roofing underlayment (hereafter called “product”) it manufactures, if installed strictly pursuant to Seller’s application instructions, that it will retain its ability to shed water, except as noted below, for a period of fifty (50) years from the sales invoice date (the “Warranty Period”). The above warranty does not apply if: 1. any part of the product is exposed to UV after roof cladding installation; and 2. the product has been installed and left uncovered without roof cladding for more than 180 days.

Buyer MUST give Seller written notice of any defects within 30 days from the date that the defect was discovered, along with field samples illustrating production codes, application details, and digital pictures. Seller reserves the right to reserve warranty claim judgment pending full field sample evaluation. Such notice shall be sent to Technical Services Manager, InterWrap Inc., 32923 Mission Way, Mission, BC, Canada, V2V-6E4. Seller shall, at its sole option and as Buyer’s sole remedy, repair or replace the product or refund the purchase price for that portion of the product that has been proven to be defective, within the written warranty conditions. Buyer shall pay all handling or transportation charges. Failure to timely give Seller notice of a defect, or unauthorized repairs or alterations, or misuse or misapplication of the product makes this warranty VOID.

This warranty applies only to products purchased between the Effective Date and the date the Seller, in its sole discretion, modifies the warranty.This warranty does not cover leaks or damage caused by any penetrations (including penetrations by fasteners), or by animals, vandalism, abusive conditions, inadequate or faulty structural design, structural defects, building alterations, natural forces such as tornados, hurricanes, earthquakes, other acts of nature, or any other cause beyond Seller's control.The warranties set forth herein are Seller’s sole and exclusive warranties. Seller’s liability on any claim of any kind for any loss or damage arising out of, in connection with, or resulting from the manufacture, sale, or resale of the product shall in no case exceed the purchase price paid for the product, prorated from the date of purchase to the date of discovery of the defect. 

In no event shall Seller be liable for other damages or for special, incidental, punitive or consequential damages.Seller makes no other warranties of any kind, express or implied, including without limitation, any warranty of merchantability or fitness for a particular purpose.No part of this warranty may be changed or cancelled except by a written document signed by Seller and Buyer. No course of dealing or performance, usage of trade or failure to enforce any term shall be used to modify the warranty. Buyer may not assign or permit any other transfer of this warranty without Seller’s consent.If any of the terms contained herein are unenforceable, such term shall be limited only to the extent necessary to make it enforceable, and all other terms shall remain in full force and effect.The warranty shall be covered by the laws of Washington, without regard to its conflicts of laws, provisions, and exclusive jurisdiction for any dispute arising from this warranty shall be in the state or federal courts of Washington.

Titanium UDL50 MSDS

I. Product Identification and Use:

Product Identification:
Titanium UDL
Product Use/Description:
Coated woven polyolefin for use as a roofing underlayment
Product Composition:
95%  polyolefin, 5% polymer blend

II. Hazardous Ingredients:
This is not a hazardous product as defined by WHMIS

III. Physical Data:

a.  Physical State:
Solid
b.  Odor and Appearance:
Pigmented odorless Woven fabric
c.  Odor threshold (ppm):
N.Ap.
d.  Vapor Pressure (mmHg):
N.Ap.
e.  Vapor Density (Air = 1):
N.Ap.
f.   Evaporation rate:
N.Ap.
g.  Boiling Point (oC):
N.Ap.
h.  Freezing Point (oC):
N.Ap.
i.   pH:
N.Ap.
j.   Specific Gravity:
N.Ap.
k. Coef. Water/oil Dist.:
N.Ap.

IV. Fire and Explosion Data:

a. Flammability:
Not flammable, but in case of a fire it will contribute.
b. Means of extinction:
Water spray and dry chemicals.
c. Flash point (oC) and Method:
N.Ap.
d. Upper flammable limit
(% by volume):

N.Ap.
e. Lower flammable limit
(% by volume):

N.Ap.
f. Hazardous combustion
products:

Carbon Monoxide, Carbon Dioxide, Nitrogen Oxides
g. Explosion Data:
Not sensitive to impact nor to static discharge.

V. Reactivity Data:

a. Chemical stability:
Yes.
b. Incompatibility with
other substances:

None
c. Reactivity:
Non-reactive
d. Hazardous decomposition
products:

No data.

VI.Toxicological properties:

a. Route of entry:
N. Ap.
b. Effects of acute exposure
to product:

None known.
c. Effects of chronic exposure
to product:

None known.
d. Exposure Limits:
Not available.
e. Irritancy of product:
N.Ap.
f. Carcinogenicity:
Not on IARC list.
g. Synergistic Products:
None known

VII. Preventive Measures:

a. Gloves:
N.Ap.
b. No respirator required under
normal use.

 
c. Leak and spill procedure:
N.Ap.
d. Waste disposal:
See your local authorities for disposal instructions.
e. Handling and Storage:
Rolls should be adequately restrained to prevent shifting during handling and storage.
f. Storage Requirements:
N.Ap.
g. Special shipping information:
None.

VIII. First aid measures:
*N.Ap.

IX. Other Information:

a. DOT Shipping Name:
Not Available
b. DOT Hazard Class:
Not Available

Prepared by: IW R&D group. (604) 820-5400
Revision Date: 25th June 2012

Disclaimer:
This information is furnished without warranty expressed or implied, except that it is accurate to the best knowledge of  InterWrap Industries Inc. The data on this sheet relates only to the specific material designated herein. InterWrap Industries Inc. assumes no legal responsibility for use or reliance upon this data.

*N.Ap. None Applicable